Information

How to make a vase with a trunk

How to make a vase with a trunk


We are searching data for your request:

Forums and discussions:
Manuals and reference books:
Data from registers:
Wait the end of the search in all databases.
Upon completion, a link will appear to access the found materials.

How to make a vase with a trunk: step-by-step instructions for making a DIY vase from a log of wood. A simple guide within everyone's reach.

A wooden vase it can be an element of great aesthetic impact for garden furniture. Making a wooden vase it is not difficult when the still intact trunks of the same trees are exploited.

How to make a vase with a trunk

A wooden vase is a good alternative to plastic or terracotta. Offers anatural plantingand perfect for different types of plants, among the most suitable we point out the evervivum.

What do you need?

  • A trunk with a diameter of about 30 cm
  • Chisel and gouge
  • Back saw
  • Topsoil
  • Plants to be planted

Note: the depth of the hollow made in the trunk must be adequate to the needs of the plants. For the evervivums it is enough to obtain a hole from a depth of 4 - 6 cm: these plants grow in nature in the cracks of the stones and in the hollows of the tuffs, they need very little soil to thrive. Evervivum plants have a low water requirement, we advise you to choose plants that do not require water in order to protect (as much as possible) the wooden trunk from humidity and rot.

For more demanding plants it will be necessary to dig a deeper excavation and, to protect the root system from water stagnation, it is possible to prepare a draining layer by placing a couple of centimeters of expanded clay on the bottom.

When making the wooden vase, do not forget to open a small drainage channel for the water to drain. For the drainage hole you do not need a drill with very long fuses ... you just need to use a saw to make a side channel capable of allowing the water to drain.

Here's how to go about turning a log into a wooden vase:

1) Grab the chisel and, with the help of the rubber-headed hammer, begin to delimit the edge of the hollow on the surface of the trunk.

2) The edge of the excavation should be delimited about 5 cm from the edge of the trunk. With the chisel, work very patiently and trying to cut the bottom by chiselling in parallel with the edges obtained. Continue in this way until the desired depth is achieved.

3) With the backsaw, make a cut on the edge of the log, this cut represents your gutter.

4) Arrange the soil at the bottom of your hollow and proceed with the planting of the chosen plants. After transplanting, be sure to fill in the gaps between the seedlings with more potting soil. Alternatively, you can have gravel or decorative stones to improve the appearance of the vase.

5) Finish the plant with a light irrigation.

To best choose the species to grow in the wooden pot obtained from a trunk, we point out some plants that need little soil and low maintenance:

  • Ajuga reptans
  • Ophiopogon planiscapus 'Nigrescens'
  • Phyla nodiflora
  • Mazus reptans
  • Isotoma fluviatilis
  • Ceratostigma plumbaginoides
  • Variable Erodium
  • Erigeron karvinskianus
  • Stachys byzanthina
  • Trifolium repens
    There are ornamental varieties with variegated and purplish leaves.
  • Oenothera speciosa
  • Leucophyta brownii
  • Dianthus
  • Sedum
    The ground cover varieties, in addition to enriching the soil area, will eventually cover the entire trunk with hanging green parts.
  • Sempervivum
    That of theeverlastingis a genus composed of 40 species of succulent plants (succulents) of the Crassulaceae family. They require little water and will preserve the integrity of yoursDIY vase with wooden trunk.
  • Fragraria
    You can also grow remontant strawberries.

In the wooden vase obtained from the trunk, you can plant Bulbosa, making sure to change the bulb at each variation of the season so as to always have a flowering trunk.



Video: How to make a beautiful slab table (May 2022).